-3 +4 do not scale from this print no of positions per row -02 thru -50 body spec -d: double row (use clp-xx-d) lead style spec -02: surface mount (use c-106-x2-xxx) (see note 9) option -p: pick & place pad (use mpp-01) (available on positon -05 thru -50 only) (not available with -pa or -k options) (see fig. 3, sht 2) -a: alignment pin (use clp-xx-d-xx) (not available with -pa option) (see fig. 3, sht 2) -tr: tape and reel -be: bottom entry only (use clp-xx-dbe-xx) -pa: pick & place pad with alignment pins (not available with -p, -a, or -k options) (see sht 2, table 3) -k: polyimide film pad (positions -05 thru -50 only) (use k-500-300, see fig. 5, sht 2) (.005[0.13] thickness with silicone adhesive) (not available with -p or -pa options) clp-1xx-xx-xxx-d-xx plating spec (values given are in micro-inches) -f: flash selective, 3 au / 50 ni min on contact, matte tin tail -l: light selective, 10 au / 50 ni min on contact, matte tin tail -s: selective, 30 au / 50 ni min on contact, matte tin tail -g: gold, 10 au / 50 ni min on contact, 3 au / 50 ni min on tail -h: heavy gold, 30 au / 50 ni min on contact, 3 au / 50 ni min on tail -lm: light selective, 10 au / 50 ni min on contact, matte tin tail -fm: flash selective, 3 au / 50 ni min on contact, matte tin tail -sm: selective, 30 au / 50 ni min on contact, matte tin tail -ltl: light selective, 10 au / 50 ni min on contact, tin/lead (90/10+/-5%) tail (no of pos x .0500[1.270]) + .017[0.43] .008[0.20] (see note 3 and 7) .120 3.05 ref .034 0.85 ref no of pos x .0500[1.270]) - .0500[1.270] (tolerance accum .0020[0.051]) .050 ref 1.27 -d -d-be clp-xx-dbe-xx .016 x .005[0.13] ref 0.41 .084 ref 2.12 "a" "a" "b" "b" -d-be -d clp-xx-d-xx c-106-22-xxx 2.5 max sway (typ) -d -d-be .170 .010 4.31 0.25 .090 - .001 + .003 2.29 - 0.03 + 0.08 (measure at bend) section "a"-"a" .004[[0.10] pos. 02-35 .006[0.15] pos. 36-50 section "b"-"b" c 01 02 fig. 1 (-d body: clp-xx-d-xx) (-d-be body: clp-xx-dbe-xx) (different as shown, otherwise same as -d body) c c c cd sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 [.3] 2 .xxx: .005 [.13] .xxxx: .0020 [.051] material: low profile .050 x .050 double row asm by: clp-1xx-xx-xxx-d-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing purvis 01/31/1994 3 1 sheet scale: 3:1 f:\dwg\misc\mktg\clp-1xx-xx-xxx-d-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 1. c represents a critical dimension 2. minimum pushout force: .5lb (8 oz) 3. one positon will be lost for every cut made on a socket strip 4. tube package positions 5-50 only. positions 2-4 are to be layered packaged. 5. shear tails to dimensions shown 6. parts to be symmetrical about c l within .0015[0.038]. 7. endwall after cutting: .0185[0.470].0025[0.064] 8. void cores may not be present. 9. hand fill use c-106-01-xx. automation use c-106-22-xx. c-106-02-xx can be subbed for c-106-22-xx. 10. max cut flash: .010[0.27] with no flash allowed in holes or extending below leads. 11. max burr: .005[.13]. insulator: lcp, ul 94 vo, color: black contact: phos bronze revision cd
.019 0.47 (no of pos x .0500[1.270]) - .100[2.54] 22.86 .005 ref (typ 4 sides) 45 x .0050 ref (typ) 0.127 .0100 ref (typ) 0.254 .025 ref (typ) 0.6350 .0070 0.178 ref (typ) "n" (see note) "q" 3.45 (see note) .250 ref 6.35 mpp-01 .100 2.54 "p" "a" "m" .325 8.26 ref "t" ppp-38-x-x-xx .121 3.07 .051 1.30 .035 ref 0.89 .275 6.99 "r" (see note) "s" (see note) .019 .010 0.48 0.25 .1575 .0050 4.000 0.127 .095 2.41 available on positions 05 thru 50 only note: "n" = used measured dimension (ref) "q" = [("n" - .250[6.35])/2] .020[0.51] fig. 3 -p: pick and place pad (available on position 05 thru 50 only) (not available with -pa or -k options) fig. 4 -pa: pick & place pad with alignment pins (not available with -p, -a or -k options) fig. 5 -k: polyimide film pad (available on position 05 thru 50 only) (not available with -p or -pa options) fig. 2 -a: alignment pin (3 position minimum) (not available with -pa option) (different as shown, otherwise same as fig. 1) note: "r" = used measured dimension (ref) "s" = {("r" - .1575[4.000])/2} .020[0.51] c c c c c c c c sheet of low profile .050 x .050 double row asm by: clp-1xx-xx-xxx-d-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing purvis 01/31/1994 3 2 sheet scale: 4:1 revision cd f:\dwg\misc\mktg\clp-1xx-xx-xxx-d-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
packaging (see note 4, sheet 1) pt-clp001-pa pt-clx-002-d pt-clx-001-d * = if applicable sheet of low profile .050 x .050 double row asm by: clp-1xx-xx-xxx-d-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing purvis 01/31/1994 3 3 sheet scale: 4:1 revision cd f:\dwg\misc\mktg\clp-1xx-xx-xxx-d-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
|
